아래 메세지는 부팅될때 나온 것 입니다.
/*===================================
WELCOME EZBOOT.X5 V1.5 ..................for PXA255
Program by You Young-chang, fooji ( J.D&T Co.,Ltd )
Last Modify 2004.03.27

Boot Flash Check ......................
Detect MX29LV400T Flash : 22B9
SIZE 4M-BIT [512Kbyte]

NAND Chip Check .......................
Detect SAMSUNG [ec:76] 64MByte
BAD BLOCK SCAN -> Kernel, Ramdisk Bad Block [0]

CS8900 Init............................
Mac Address : [00 A2 55 F2 26 25]
Detect value : [3000:3000]
Chip ID : [0E63:000A]


Copy Kernel Image .....
Copy Ramdisk Image .....
Starting kernel [MARCH 303]...
Uncompressing Linux....................................................
done, bo
oting the kernel.
Linux version 2.4.19-rmk7-pxa1 (root@jdt) (gcc version 3.2.1) #272 Mon
Jan 5 12:
35:59 KST 2004
CPU: XScale-PXA255 revision 6
Machine: WWW.FALINUX.COM EZ-X5 for PXA255 Board
Ignoring unrecognised tag 0x00000000
initrd (0x00800000 - 0x00c00000) extends beyond physical memory -
disabling init
rd
Memory clock: 99.53MHz (*27)
Run Mode clock: 398.13MHz (*4)
Turbo Mode clock: 398.13MHz (*1.0, inactive)
On node 0 totalpages: 16384
zone(0): 16384 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: y initrd=0x0800000,4M root=/dev/ram ramdisk=10240
console=
ttyS02,115200 ip0=192.168.10.155 nandparts=1,4,59
Console: colour dummy device 80x30
Calibrating delay loop... 397.31 BogoMIPS
Memory: 64MB = 64MB total
Memory: 63016KB available (1384K code, 319K data, 68K init)
Dentry cache hash table entries: 8192 (order: 4, 65536 bytes)
Inode cache hash table entries: 4096 (order: 3, 32768 bytes)
Mount-cache hash table entries: 1024 (order: 1, 8192 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Using PXA255 frequency points.
Registering CPU frequency change support.
CPU clock: 398.131 MHz (99.000-400.000 MHz)
Starting kswapd
Console: switching to colour frame buffer device 80x30
LCD resolution 640x480
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with no serial options enabled
ttyS00 at 0x0000 (irq = 15) is a PXA UART
ttyS01 at 0x0000 (irq = 14) is a PXA UART
ttyS02 at 0x0000 (irq = 13) is a PXA UART
mk712 device OK!
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 50MHz system bus speed for PIO modes; override with
idebus=xx
eth0: cs8900 rev K Base 0xF1000300<6>, IRQ 44, MAC 00:A2:55:F2:26:25
RAMDISK driver initialized: 16 RAM disks of 10240K size 1024 blocksize
loop: loaded (max 8 devices)
NAND device: Manufacture ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MB 3,3V)
Creating 3 MTD partitions on "NAND 64MB 3,3V":
0x00000000-0x00100000 : "EZ-X5 Kernel partition"
0x00100000-0x00500000 : "EZ-X5 Ramdisk partition"
0x00500000-0x04000000 : "EZ-X5 Data partition 0"
MMC subsystem, $Revision: 0.3.1.14 $
MMC block device driver, $Revision: 0.3.1.16 $
PXA250 MMC controller driver, $Revision: 0.3.1.12 $
Linux Kernel Card Services 3.1.22
options: none
Intel PXA250/210 PCMCIA (CS release 3.1.22)
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 8192)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NetWinder Floating Point Emulator V0.95 (c) 1998-1999 Rebel.com
FAT: bogus logical sector size 65471
yaffs: dev is 256 name is "01:00"
VFS: Mounted root (yaffs filesystem) readonly.
Freeing init memory: 68K
Warning: unable to open an initial console.
Kernel panic: No init found. Try passing init= option to kernel.


WELCOME EZBOOT.X5 V1.5 ..................for PXA255
Program by You Young-chang, fooji ( J.D&T Co.,Ltd )
Last Modify 2004.03.27

Boot Flash Check ......................
Detect MX29LV400T Flash : 22B9
SIZE 4M-BIT [512Kbyte]

NAND Chip Check .......................
Detect SAMSUNG [ec:76] 64MByte
BAD BLOCK SCAN -> Kernel, Ramdisk Bad Block [0]

CS8900 Init............................
Mac Address : [00 A2 55 F2 26 25]
Detect value : [3000:3000]
Chip ID : [0E63:000A]

Quickly Autoboot [ENTER] / Goto BOOT-MENU press [space bar]

EZBOOT>set


^^;
1. MAC Address [00:a2:55:f2:26:25]
2. LOCAL IP [192.168.10.155]
3. HOST IP [0.0.0.0]
4. Host tftp directory []
5. zImage file name [zImage.x5]
6. ram disk file name [ramdisk.x5.gz]
7. boot loader file name [ezboot.x5]

A. Autoboot wait time [3]
B. Boot Menu Key [ ]
C. Copy Ramdisk [Y/N] [Y]
D. Architecture Number [303]
E. Serial FF/BT/ST(0/1/2) [2]
F. NAND-Partition MByte (kernel:ramdisk:app) [1:4:59]
W. Watchdog (sec, off=0) [0]

K. Kernel CMD 1st [initrd=0x0800000,4M root=/dev/ram ramdisk=10240]
M. Kernel CMD 2nd [console=ttyS02,115200]
N. Kernel CMD 3rd []

L. Load Default
P. Apply & Exit
S. Save
0. Exit

Select >>

//===========================*/


이상입니다.

이미지는 씨디에 있는 것입니다.

zImage.x5.pcmcia
ramdisk.x5.pcmcia-10M.gz

이것 수정 없이 올린 상황 입니다.

왜그런지 알려주세요...
그럼 수고하세요...^^