도와주세요!!
2005.06.22 19:10:04 (*.125.126.232)
7397
1. 부팅메시지입니다.
Linux version 2.4.19-rmk7-pxa1 (root@localhost.localdomain) (gcc version
3.2.1) #432 2005. 06. 17. (금) 18:41:39 KST
CPU: XScale-PXA255 revision 6
Machine: WWW.FALINUX.COM EZ-X5 for PXA255 Board
Ignoring unrecognised tag 0x00000000
Memory clock: 99.53MHz (*27)
Run Mode clock: 398.13MHz (*4)
Turbo Mode clock: 398.13MHz (*1.0, inactive)
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=1f04 mem=32M initrd=0xa0800000,4M
root=/dev/ram ramdisk=10240 console=ttyS02,115200 ip0=192.168.10.155
nandparts=1,4,59
Relocating machine vectors to 0xffff0000
Console: colour dummy device 80x30
Calibrating delay loop... 397.31 BogoMIPS
Memory: 32MB = 32MB total
Memory: 26480KB available (1429K code, 297K data, 68K init)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Using PXA255 frequency points.
Registering CPU frequency change support.
CPU clock: 398.131 MHz (99.000-400.000 MHz)
Starting kswapd
yaffs Jun 17 2005 18:42:33 Initialisation
yaffs is using generic read/write (caching)
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
I2C: PXA algorithm module loaded.
I2C: Adding PXA-I2C-Adapter.
i2c-dev.o: Registered 'PXA-I2C-Adapter' as minor 0
I2C: Scanning bus (68)
I2C: Successfully added bus
Console: switching to colour frame buffer device 80x30
LCD resolution 640x480
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with no serial options enabled
ttyS00 at 0x0000 (irq = 15) is a PXA UART
ttyS01 at 0x0000 (irq = 14) is a PXA UART
ttyS02 at 0x0000 (irq = 13) is a PXA UART
mk712 device OK!
I2C: DS1307 RTC driver successfully loaded
eth0: cs8900 rev K Base 0xF1000300<6>, IRQ 44, MAC 00:A2:55:F2:26:25
RAMDISK driver initialized: 16 RAM disks of 10240K size 1024 blocksize
loop: loaded (max 8 devices)
SCSI subsystem driver Revision: 1.00
NAND device: Manufacture ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MB 3,3V)
Creating 3 MTD partitions on "NAND 64MB 3,3V":
0x00000000-0x00100000 : "EZ-X5 Kernel partition"
0x00100000-0x00500000 : "EZ-X5 Ramdisk partition"
0x00500000-0x04000000 : "EZ-X5 Data partition 0"
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
host/sl811.c: v0.30 : Sl811 USB Host Controller Alternate Driver
usb.c: new USB bus registered, assigned bus number 1
host/sl811.c: USB SL811 at f2000000,f2000004, IRQ 35
hub.c: USB hub found
hub.c: 1 port detected
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NetWinder Floating Point Emulator V0.95 (c) 1998-1999 Rebel.com
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 4096K
VFS: Mounted root (ext2 filesystem) readonly.
Freeing init memory: 68K
yaffs: dev is 7938 name is "1f:02"
yaffs: Attempting MTD mount on 31.2, "1f:02"
2. filesystems의 내용입니다.
nodev rootfs
nodev bdev
nodev proc
nodev sockfs
nodev tmpfs
nodev pipefs
ext2
nodev ramfs
umsdos
msdos
vfat
nodev nfs
nodev devpts
yaffs
nodev usbdevfs
nodev usbfs
3. USB 1.1 만 지원한다는 것은 USB2.0을 1.1로 인식한다는 의미인지, 아니면
아예 USB1.1 로 나온 옛날 USB 메모리만 지원된다는 것인지 궁금합니다.
장형기 wrote..
: 안녕하세요..
:
: 다음의 내용을 그렙하셨어 올려 주세요..
:
: 1. 커널 부팅 메세지..
:
: $ dmesg 하시면 나오는 메세지를 올려 주세요..
:
:
: 2. $ cat /proc/filesystem 하셨어 나오는 메세지를 올려 주세요...
:
:
:
: 참고로 저희가 TEST한 USB 메로리 스틱은 다음과 같습니다.
:
: 1. SS코리아 D-Drive 128M
:
: 2. 넥스디스크(NEXDISK) 64M
:
:
: EZ-PI 보드의 USB-HOST의 Interface는 USB 1.1 만을 지원합니다...
:
:
:
: gabi wrote..
: : EZ-PI 보드를 사용하여 USB mass stroage 에 1초에 한번씩 파일로 저장하 려고
: : 합니다.
: :
: : 현재 CD의 버전은 041117 이고, 보드상에서 uname -a 의 결과는 linux ez- x5
: : 2.4.19-rmk7-pxa1 로 나옵니다. CD상의 image내의 커널과 램디스크를 ezboot
: : 를 사용하여 다운받아 사용합니다.
: :
: : unidrive 256M 와 CELLDISK2.0 1G를 사용하는데 둘다 문제가 있습니다.
: : 둘다 윈도우에서 FAT32로 포맷하였습니다.
: :
: : unidrive의 경우 USB를 연결하면
: : partition check:
: : sda : unknown partition table
: : 로 나오고 lsusb에는 잘 잡혀있습니다만
: : mount 시에
: : mount: Mounting /dev/sda1 on /mnt/ums failed: No such device or address
: : 가 뜹니다.
: :
: : CELLDISK2.0의 경우에는 USB를 연결하면 조금후
: : hub.c: USB disconnect on device SL811-1.1 address 7
: : hub.c: USB device not accepting new address (error=-110)
: : hub.c: error resetting hub 6 - disconnecting
: : usb.c: USB disconnect on device SL811-1 address 6
: : 이라는 메시지가 뜨고
: : lsusb에도 잡히지 않습니다.
: :
: : 해결방법이 있다면 알려주시고,
: : 혹 그게 아니라면 1G USB 메모리 스틱중에
: : EZ-PI 보드와 잘 동작되는 것이 있으면 알려주시면 고맙겠습니다.
Linux version 2.4.19-rmk7-pxa1 (root@localhost.localdomain) (gcc version
3.2.1) #432 2005. 06. 17. (금) 18:41:39 KST
CPU: XScale-PXA255 revision 6
Machine: WWW.FALINUX.COM EZ-X5 for PXA255 Board
Ignoring unrecognised tag 0x00000000
Memory clock: 99.53MHz (*27)
Run Mode clock: 398.13MHz (*4)
Turbo Mode clock: 398.13MHz (*1.0, inactive)
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=1f04 mem=32M initrd=0xa0800000,4M
root=/dev/ram ramdisk=10240 console=ttyS02,115200 ip0=192.168.10.155
nandparts=1,4,59
Relocating machine vectors to 0xffff0000
Console: colour dummy device 80x30
Calibrating delay loop... 397.31 BogoMIPS
Memory: 32MB = 32MB total
Memory: 26480KB available (1429K code, 297K data, 68K init)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Using PXA255 frequency points.
Registering CPU frequency change support.
CPU clock: 398.131 MHz (99.000-400.000 MHz)
Starting kswapd
yaffs Jun 17 2005 18:42:33 Initialisation
yaffs is using generic read/write (caching)
i2c-core.o: i2c core module
i2c-dev.o: i2c /dev entries driver module
I2C: PXA algorithm module loaded.
I2C: Adding PXA-I2C-Adapter.
i2c-dev.o: Registered 'PXA-I2C-Adapter' as minor 0
I2C: Scanning bus (68)
I2C: Successfully added bus
Console: switching to colour frame buffer device 80x30
LCD resolution 640x480
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with no serial options enabled
ttyS00 at 0x0000 (irq = 15) is a PXA UART
ttyS01 at 0x0000 (irq = 14) is a PXA UART
ttyS02 at 0x0000 (irq = 13) is a PXA UART
mk712 device OK!
I2C: DS1307 RTC driver successfully loaded
eth0: cs8900 rev K Base 0xF1000300<6>, IRQ 44, MAC 00:A2:55:F2:26:25
RAMDISK driver initialized: 16 RAM disks of 10240K size 1024 blocksize
loop: loaded (max 8 devices)
SCSI subsystem driver Revision: 1.00
NAND device: Manufacture ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MB 3,3V)
Creating 3 MTD partitions on "NAND 64MB 3,3V":
0x00000000-0x00100000 : "EZ-X5 Kernel partition"
0x00100000-0x00500000 : "EZ-X5 Ramdisk partition"
0x00500000-0x04000000 : "EZ-X5 Data partition 0"
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
host/sl811.c: v0.30 : Sl811 USB Host Controller Alternate Driver
usb.c: new USB bus registered, assigned bus number 1
host/sl811.c: USB SL811 at f2000000,f2000004, IRQ 35
hub.c: USB hub found
hub.c: 1 port detected
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NetWinder Floating Point Emulator V0.95 (c) 1998-1999 Rebel.com
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 4096K
VFS: Mounted root (ext2 filesystem) readonly.
Freeing init memory: 68K
yaffs: dev is 7938 name is "1f:02"
yaffs: Attempting MTD mount on 31.2, "1f:02"
2. filesystems의 내용입니다.
nodev rootfs
nodev bdev
nodev proc
nodev sockfs
nodev tmpfs
nodev pipefs
ext2
nodev ramfs
umsdos
msdos
vfat
nodev nfs
nodev devpts
yaffs
nodev usbdevfs
nodev usbfs
3. USB 1.1 만 지원한다는 것은 USB2.0을 1.1로 인식한다는 의미인지, 아니면
아예 USB1.1 로 나온 옛날 USB 메모리만 지원된다는 것인지 궁금합니다.
장형기 wrote..
: 안녕하세요..
:
: 다음의 내용을 그렙하셨어 올려 주세요..
:
: 1. 커널 부팅 메세지..
:
: $ dmesg 하시면 나오는 메세지를 올려 주세요..
:
:
: 2. $ cat /proc/filesystem 하셨어 나오는 메세지를 올려 주세요...
:
:
:
: 참고로 저희가 TEST한 USB 메로리 스틱은 다음과 같습니다.
:
: 1. SS코리아 D-Drive 128M
:
: 2. 넥스디스크(NEXDISK) 64M
:
:
: EZ-PI 보드의 USB-HOST의 Interface는 USB 1.1 만을 지원합니다...
:
:
:
: gabi wrote..
: : EZ-PI 보드를 사용하여 USB mass stroage 에 1초에 한번씩 파일로 저장하 려고
: : 합니다.
: :
: : 현재 CD의 버전은 041117 이고, 보드상에서 uname -a 의 결과는 linux ez- x5
: : 2.4.19-rmk7-pxa1 로 나옵니다. CD상의 image내의 커널과 램디스크를 ezboot
: : 를 사용하여 다운받아 사용합니다.
: :
: : unidrive 256M 와 CELLDISK2.0 1G를 사용하는데 둘다 문제가 있습니다.
: : 둘다 윈도우에서 FAT32로 포맷하였습니다.
: :
: : unidrive의 경우 USB를 연결하면
: : partition check:
: : sda : unknown partition table
: : 로 나오고 lsusb에는 잘 잡혀있습니다만
: : mount 시에
: : mount: Mounting /dev/sda1 on /mnt/ums failed: No such device or address
: : 가 뜹니다.
: :
: : CELLDISK2.0의 경우에는 USB를 연결하면 조금후
: : hub.c: USB disconnect on device SL811-1.1 address 7
: : hub.c: USB device not accepting new address (error=-110)
: : hub.c: error resetting hub 6 - disconnecting
: : usb.c: USB disconnect on device SL811-1 address 6
: : 이라는 메시지가 뜨고
: : lsusb에도 잡히지 않습니다.
: :
: : 해결방법이 있다면 알려주시고,
: : 혹 그게 아니라면 1G USB 메모리 스틱중에
: : EZ-PI 보드와 잘 동작되는 것이 있으면 알려주시면 고맙겠습니다.
