Quickly Autoboot [ENTER] / Goto BOOT-MENU press [space bar].....
Copy Kernel Image .....
Copy Ramdisk Image .....
Starting kernel [MARCH 303]...
Uncompressing Linux..................................................... done, .Linux version 2.4.19-rmk7-pxa1 (root@jdt) (gcc version 3.2.1) #419 Mon Nov 22 14CPU: XScale-PXA255 revision 6
Machine: WWW.FALINUX.COM EZ-X5 for PXA255 Board
Ignoring unrecognised tag 0x00000000
Memory clock: 99.53MHz (*27)
Run Mode clock: 398.13MHz (*4)
Turbo Mode clock: 398.13MHz (*1.0, inactive)
On node 0 totalpages: 16384
zone(0): 16384 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: y  initrd=0xa0800000,4M root=/dev/ram ramdisk=10240 consol3Console: colour dummy device 80x30
Calibrating delay loop... 397.31 BogoMIPS
Memory: 64MB = 64MB total
Memory: 58908KB available (1412K code, 302K data, 68K init)
Dentry cache hash table entries: 8192 (order: 4, 65536 bytes)
Inode cache hash table entries: 4096 (order: 3, 32768 bytes)
Mount-cache hash table entries: 1024 (order: 1, 8192 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Using PXA255 frequency points.
Registering CPU frequency change support.
CPU clock: 398.131 MHz (99.000-400.000 MHz)
Starting kswapd
I2C: PXA algorithm module loaded.
I2C: Adding PXA-I2C-Adapter.
i2c-dev.o: Registered 'PXA-I2C-Adapter' as minor 0
I2C: Scanning bus
I2C: Successfully added bus
Console: switching to colour frame buffer device 80x30
LCD resolution 640x480
Detected PS/2 Mouse Port.
PS2 Keyboard base:0xf1100000, irq:31 (gpio-8)
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with no serial options enabled
ttyS00 at 0x0000 (irq = 15) is a PXA UART
ttyS01 at 0x0000 (irq = 14) is a PXA UART
ttyS02 at 0x0000 (irq = 13) is a PXA UART
mk712 device OK!
I2C: DS1307 RTC driver successfully loaded
eth0: cs8900 rev K Base 0xF1000300<6>, IRQ 44, MAC 00:A2:55:F2:26:25
RAMDISK driver initialized: 16 RAM disks of 10240K size 1024 blocksize
loop: loaded (max 8 devices)
SCSI subsystem driver Revision: 1.00
ac97_codec: AC97 Audio codec, id: 0x4352:0x5973 (Cirrus Logic CS4202)
CS4202 is not ready ... error!
NAND device: Manufacture ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MB 3,3V)
Creating 3 MTD partitions on "NAND 64MB 3,3V":
0x00000000-0x00100000 : "EZ-X5 Kernel partition"
0x00100000-0x01f00000 : "EZ-X5 Ramdisk partition"
0x01f00000-0x04000000 : "EZ-X5 Data partition 0"
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
host/sl811.c: v0.30 : Sl811 USB Host Controller Alternate Driver
usb.c: new USB bus registered, assigned bus number 1
host/sl811.c: USB SL811 at f2000000,f2000004, IRQ 35
hub.c: USB hub found
hub.c: 1 port detected
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 8192)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NetWinder Floating Point Emulator V0.95 (c) 1998-1999 Rebel.com
RAMDISK: Compressed image found at block 0
RAMDISK: incomplete write (-28 != 32768), only wrote 10485760
Freeing initrd memory: 4096K
VFS: Mounted root (ext2 filesystem) readonly.
Freeing init memory: 68K
Warning: unable to open an initial console.
attempt to access beyond end of device
01:00: rw=0, want=841835629, limit=10240
attempt to access beyond end of device
01:00: rw=0, want=841835629, limit=10240
Kernel panic: No init found.  Try passing init= option to kernel.

----------------------------------------------------------------------------------
램디스크이미지는 4메가 이하이고..
이미지 압축해제시 29메가 정도 되더군요..
그래서 파티션을 1:30:33으로 바꿨습니다.
커널은 그대로 이고요..
커널을 수정해야 하나요?
램디스크 이미지가 4메가 이하라서 수정 안했는데..
아시는분 답변 부탁드립니다..
참고로 램디스크는 자료실에 있는 페도라코어3용.. 커널 2.4.19용으로 수정하였습니다.