1. 아직 lcd에 부팅 되는걸 보지 못했습니다.  2440에 lcd는 480x272인데여... 첨에 보드에 640x480으로 세팅 되어있길래.. CD에 있는 커널이미지 파일로 480으로 변경했습니다. 그리고 부팅을 했는데 아무것도 뜨지가 않네여. 화면은 전원을 올렸을 때 꺼진상태에서 회색 빛으로 바뀌구여.이게 백라이트 켜진게 맞나여? 밝아져는데 부팅화면이 안보여서 이게 켜진 상태인지? (처음 연결했을때 1초 부팅화면이 켜지기 전에 보드랑 lcd전원이 나갔거든여. 오늘 새로 해보니 전원은 둘 다 잘 들어옵니다.)
백라이트는 켜진거 같거든여.. 제 생각에... 새로 이지부트도 올려봤거든여..

원래 설정이 콘솔 화면이 안보이게 되있나여? hexdump를 이용해서 터치는 인식하거든여...

qt로 만든 hello도 에러없이 다 실행 시켜도 반응이 없습니다.

초보라서 질문이 많네여...lcd 자체가 고장이면 안되는데... 이번달에 사서 2틀전에 첨 lcd 연결한거라서...
저도 부팅 펭귄 보고 싶네여... 답변 부탁합니다.  menuconfig에서 framebuffer설정해도 안되네여...
부팅화면 붙입니다.

                                                             ...
Copy Kernel Image .....
Copy Ramdisk Image .....
Starting kernel [MARCH 3007]...
kernel command [EZBOOT mem=64M initrd=0x30800000,5M root=/dev/ram0 ramdisk=12288
 console=ttySAC2,115200    ip0=192.168.10.160 mac=00:FA:08:14:01:09 netmask=255.
255.255.0 gw=192.168.10.1 host=211.206.210.176 nandparts=2,8,54 ]
Uncompressing Linux.............................................................
............................................................ done, booting the k
ernel.
Linux version 2.6.21-falinux (gemini@hw27) (gcc version 3.4.3) #1 Thu Jan 24 17:
51:49 KST 2008
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
Machine: www.falinux.com EDK-S3C2440 for S3C2440 Board
Memory policy: ECC disabled, Data cache writeback
CPU S3C2440A (id 0x32440001)
S3C244X: core 399.651 MHz, memory 133.217 MHz, peripheral 66.608 MHz
S3C24XX Clocks, (c) 2004 Simtec Electronics
CLOCK: Slow mode (2.116 MHz), fast, MPLL on, UPLL on
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Built 1 zonelists.  Total pages: 16256
Kernel command line: EZBOOT mem=64M initrd=0x30800000,5M root=/dev/ram0 ramdisk=
12288 console=ttySAC2,115200    ip0=192.168.10.160 mac=00:FA:08:14:01:09 netmask
=255.255.255.0 gw=192.168.10.1 host=211.206.210.176 nandparts=2,8,54
irq: clearing pending status 00000400
irq: clearing subpending status 00000080
PID hash table entries: 256 (order: 8, 1024 bytes)
timer tcon=00000009, tcnt d8d2, tcfg 000002ff,00003333, usec 0000170f
Console: colour dummy device 80x30
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 55936KB available (3336K code, 383K data, 132K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
S3C2440: Initialising architecture
S3C2440: IRQ Support
S3C2440: Clock Support, DVS off
S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics
DMA channel 0 at c4800000, irq 33
DMA channel 1 at c4800040, irq 34
DMA channel 2 at c4800080, irq 35
DMA channel 3 at c48000c0, irq 36
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 5120K
NetWinder Floating Point Emulator V0.97 (double precision)
audit: initializing netlink socket (disabled)
audit(2.315:1): initialized
yaffs Jan 24 2008 17:49:33 Installing.
io scheduler noop registered (default)
fb0: s3c2410fb frame buffer device ( 480x272x16 )
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
s3c2440-uart.0: s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440
s3c2440-uart.1: s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440
s3c2440-uart.2: s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440
RAMDISK driver initialized: 16 RAM disks of 12288K size 1024 blocksize
loop: loaded (max 8 devices)
AX88796B: v1.1.0
AX88796B: 09/20/06 (http://www.asix.com.tw)
ax88796b: MAC ADDRESS  00 fa 08 14 01 09
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c2440-nand s3c2440-nand: Tacls=3, 22ns Twrph0=8 60ns, Twrph1=3 22ns
NAND device: Manufacturer ID:0xec, Chip ID:0x76 (Samsung NAND 64MiB 3,3V 8-bit)
Scanning device for bad blocks
Creating 3 MTD partitions on "NAND 64MiB 3,3V 8-bit":
0x00000000-0x00200000 : "falinux boot/config/logo partition"
0x00200000-0x00a00000 : "falinux kernel/ramdisk partition"
0x00a00000-0x04000000 : "falinux yaffs partition"
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
s3c2410 TouchScreen successfully loaded
input: s3c2410 TouchScreen as /class/input/input0
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
i2c /dev entries driver
s3c2440-i2c s3c2440-i2c: slave address 0x10
s3c2440-i2c s3c2440-i2c: bus frequency set to 378 KHz
s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
mapped channel 0 to 0
s3c2440-sdi s3c2440-sdi: initialisation done.
Advanced Linux Sound Architecture Driver Version 1.0.14rc3.
ASoC version 0.13.0
AC97 SoC Audio Codec 0.6
asoc: AC97 HiFi <-> s3c2440-ac97 mapping ok
ALSA device list:
  #0: FALINUXS3C2440 (AC97)
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
IPv6 over IPv4 tunneling driver
sit0: Disabled Privacy Extensions
NET: Registered protocol family 17
s3c2410-rtc s3c2410-rtc: hctosys: invalid date/time
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem) readonly.
Freeing init memory: 132K
INIT: version 2.86 booting
INIT: Entering runlevel: 3
yaffs: dev is 32505858 name is "mtdblock2"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.2, "mtdblock2"
yaffs: auto selecting yaffs1
eth0 Link mode : 100 Mb/s  Duplex mode.
Starting system logger: [  OK  ]
Starting INET services: [  OK  ]

Welcome to FALinux (www.falinux.com)
Linux Kernel 2.6.21-falinux
falinux login: