계속 시도해 봤는데.. 되지 않아 질문올립니다.

먼저..
host 는 210.94.173.104 이고
ezboard 는 210.94.173.103 입니다.
gateway 는 210.94.173.2

ezboot에서..
set 해서

1. MAC Address [00:d0:ca:f2:26:25]
2. LOCAL IP [210.94.173.103]
3. HOST IP [210.94.173.104]
4. Host tftp directory []
5. zImage file name [zImage]
6. ram disk file name [ramdisk.gz]
7. boot loader file name [ezboot]
8. zImage address on flash [0x00020000]
9. ramdisk address on flash [0x00200000]
A. zImage address on memory [0xc0008000]
B. ramdisk address on memory [0xc0800000]
C. Autoboot wait time [3]
D. Boot Menu Key [ ]
E. Kernel Command Line []
F. Architecture Number [200]
G. RAM Disk Size MBytes [8]

같이 했습니다.

저장한 후에.. 호스트로 ping 하면..
EZBOOT>ping 210.94.173.104
Send ARP Packet
Send ARP Packet
Send ARP Packet
Send ARP Packet
Send ARP Packet
Send ARP Packet
Send ARP Packet
Send ARP Packet
Send ARP Packet
Send ARP Packet

같이 나옵니다. 현재 LINK에 불 들어와 있구요.. ping 하는 도중에는 ACT가 반
짜거립니다.
이게 정상적인건가요? 패킷을 받았다는 메세지가 안뜹니다.. ㅠ_ㅠ

그리고.. 이젠.. ezboot 말고 부팅해서는..
ifconfig 하면..
[root@ezboard /root]$ ifconfig
eth0 Link encap:Ethernet HWaddr 00:D0:CA:F2:26:25
inet addr:210.94.173.103 Bcast:210.94.173.255
Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
Interrupt:47 Base address:0x300

lo Link encap:Local Loopback
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
가 뜹니다..

ping을 해보면..
[root@ezboard /root]$ ping 210.94.173.104
PING 210.94.173.104 (210.94.173.104): 56 data bytes

하고.. 계속 멈춰있습니다. 그래서.. ctrl + c 누르면..

--- 210.94.173.104 ping statistics ---
942 packets transmitted, 0 packets received, 100% packet loss

나옵니다. ㅜ_ㅜ

그래서.. 혹시나 하는 맘으로..

[root@ezboard /root]$ ifconfig lo up
[root@ezboard /root]$ ifconfig eth0 210.94.173.103 netmask 255.255.255.0
up
[root@ezboard /root]$ route add default gw 210.94.173.2 eth0
[root@ezboard /root]$ ifconfig
eth0 Link encap:Ethernet HWaddr 00:D0:CA:F2:26:25
inet addr:210.94.173.103 Bcast:210.94.173.255
Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:942 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
Interrupt:47 Base address:0x300

lo Link encap:Local Loopback
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0

[root@ezboard /root]$ ping 210.94.173.104
PING 210.94.173.104 (210.94.173.104): 56 data bytes

--- 210.94.173.104 ping statistics ---
15 packets transmitted, 0 packets received, 100% packet loss

로 나옵니다. ㅜ_ㅜ

딴 컴퓨터에서 호스트로 ping 하면 작동이 잘 되는데요.. ezboard에서는 안되
네요.. ㅠ_ㅠ
제가... 어떻게 해야 할까요... 도움을 주세요.. ㅜ_ㅜ