도와주세요!!
2005.08.11 18:00:28 (*.244.144.199)
21481
WELCOME EZBOOT.X5 V1.5 ..................for PXA255
Program by You Young-chang, fooji ( J.D&T Co.,Ltd )
Last Modify 2004.03.27
Boot Flash Check ......................
Detect MX29LV400T Flash : 22B9
SIZE 4M-BIT [512Kbyte]
NAND Chip Check .......................
Detect SAMSUNG [ec:76] 64MByte
BAD BLOCK SCAN -> Kernel, Ramdisk Bad Block [1]
CS8900 Init............................
Mac Address : [00 A2 55 F2 26 25]
Detect value : [3000:3000]
Chip ID : [0E63:000A]
..
Copy Kernel Image .....
Copy Ramdisk Image .....
Starting kernel [MARCH 303]...
Uncompressing Linux..................................................... done, .
Linux version 2.4.19-rmk7-pxa1 (root@localhost) (gcc version 3.2.1) #423 일 7월5
CPU: XScale-PXA255 revision 6
Machine: WWW.FALINUX.COM EZ-X5 for PXA255 Board
Ignoring unrecognised tag 0x00000000
Memory clock: 99.53MHz (*27)
Run Mode clock: 398.13MHz (*4)
Turbo Mode clock: 398.13MHz (*1.0, inactive)
On node 0 totalpages: 16384
zone(0): 16384 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: y initrd=0xa0800000,4M root=/dev/ram ramdisk=10240 consol9
Console: colour dummy device 80x30
Calibrating delay loop... 397.31 BogoMIPS
Memory: 64MB = 64MB total
Memory: 58908KB available (1416K code, 298K data, 68K init)
Dentry cache hash table entries: 8192 (order: 4, 65536 bytes)
Inode cache hash table entries: 4096 (order: 3, 32768 bytes)
Mount-cache hash table entries: 1024 (order: 1, 8192 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Using PXA255 frequency points.
Registering CPU frequency change support.
CPU clock: 398.131 MHz (99.000-400.000 MHz)
Starting kswapd
I2C: PXA algorithm module loaded.
I2C: Adding PXA-I2C-Adapter.
i2c-dev.o: Registered 'PXA-I2C-Adapter' as minor 0
I2C: Scanning bus (68)
I2C: Successfully added bus
Console: switching to colour frame buffer device 80x30
LCD resolution 640x480
initialize_kbd: Keyboard interface failed self test
Detected PS/2 Mouse Port.
PS2 Keyboard base:0xf1100000, irq:31 (gpio-8)
pty: 256 Unix98 ptys configured
keyboard: Timeout - AT keyboard not present?(ed)
keyboard: Timeout - AT keyboard not present?(f4)
Serial driver version 5.05c (2001-07-08) with no serial options enabled
ttyS00 at 0x0000 (irq = 15) is a PXA UART
ttyS01 at 0x0000 (irq = 14) is a PXA UART
ttyS02 at 0x0000 (irq = 13) is a PXA UART
mk712 device OK!
I2C: DS1307 RTC driver successfully loaded
eth0: cs8900 rev K Base 0xF1000300<6>, IRQ 44, MAC 00:A2:55:F2:26:25
RAMDISK driver initialized: 16 RAM disks of 10240K size 1024 blocksize
loop: loaded (max 8 devices)
Linux video capture interface: v1.00
SCSI subsystem driver Revision: 1.00
ac97_codec: AC97 Audio codec, id: 0x4352:0x5973 (Cirrus Logic CS4202)
NAND device: Manufacture ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MB 3,3V)
Creating 3 MTD partitions on "NAND 64MB 3,3V":
0x00000000-0x00100000 : "EZ-X5 Kernel partition"
0x00100000-0x00500000 : "EZ-X5 Ramdisk partition"
0x00500000-0x04000000 : "EZ-X5 Data partition 0"
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
host/sl811.c: v0.30 : Sl811 USB Host Controller Alternate Driver
usb.c: new USB bus registered, assigned bus number 1
host/sl811.c: USB SL811 at f2000000,f2000004, IRQ 35
hub.c: USB hub found
hub.c: 1 port detected
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 8192)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NetWinder Floating Point Emulator V0.95 (c) 1998-1999 Rebel.com
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 4096K
VFS: Mounted root (ext2 filesystem) readonly.
Freeing init memory: 68K
INIT: version 2.84 booting
EXT2-fs warning: maximal mount count reached, running e2fsck is recommended
INIT: Entering runlevel: 3
yaffs: dev is 7938 name is "1f:02"
hub.c: new USB device SL811-1, assigned address 2
mount: Mounting usbdevfs on /proc/bus/usb failed: Device or resource busy
Using /lib/pwc.o
pwc Philips PCA645/646 + PCVC675/680/690 + PCVC730/740/750 webcam module versio.
pwc Also supports the Askey VC010, Logitech Quickcam 3000 Pro, Samsung MPC-C10 ,
pwc the Creative WebCam 5, SOTEC Afina Eye and Visionite VCS-UC300 and VCS-UM10.
usb.c: registered new driver Philips webcam
Using /lib/pwcx-ezx5.o
insmod: Warning: kernel-module version mismatch
/lib/pwcx-ezx5.o was compiled for kernel version 2.4.20
while this kernel is version 2.4.19-rmk7-pxa1
Warning: loading pwcx-ezx5 will taint the kernel: non-GPL license - NDA-ed. Spw2
ee http://www.smcc.demon.nl/webcam/tainting.html
See http://wpwc Supports all cameras supported by the main module (pwc).
ww.tux.org/lkml/#export-tainted for information about tainted modules
Warning: loading pwcx-ezx5 will taint the kernel: forced load
Using /lib/motor_control_dev.o
Warning: loading motor_control_dev will taint the kernel: no lic Init madule, S]
ense
See http://www.tux.org/lkml/#export-tainted for informat/nctrl :0, duty : 6, s
Interrupt Motor Register Ok...
Interrupt Timer Register Ok...
Starting system logger: syslogd
Starting INET services: inetd
Welcome to J.D&T EZ-X5 ( www.falinux.com )
XScale(PXA255) Linux
ez-x5 login: usb_control/bulk_msg: timeout
usb.c: failed to set device 2 default configuration (error=-110)
hub.c: new USB device SL811-1, assigned address 3
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=3 (error=-110)
Welcome to J.D&T EZ-X5 ( www.falinux.com )
XScale(PXA255) Linux
ez-x5 login:
----------------------------------------------------------------------------------
부팅시 메시지 입니다...위의 부팅은 rc.local 파일을 수정 해서 부팅과 동시에 모듈이 올라가게 수정 했습ㄴ다. 수정 내용은 처음 질문 글과 같습니다....
l------------------------------------------------------------------------------
lsmod 명령어 실행시
Module Size Used by Tainted: PF
motor_control_dev 5392 0 (unused)
pwcx-ezx5 89044 0 (autoclean) (unused)
pwc 42008 0 [pwcx-ezx5]
-------------------------------------------------------------------------
mvc 실행시 오류 내용
[root@ez-x5 /root]$ mvc
MVC version 0.8.9
Press CTRL-Z to switch program to daemon mode.
Can't open device /dev/video0
v4l init fault!
-----------------------------------------------------
Program by You Young-chang, fooji ( J.D&T Co.,Ltd )
Last Modify 2004.03.27
Boot Flash Check ......................
Detect MX29LV400T Flash : 22B9
SIZE 4M-BIT [512Kbyte]
NAND Chip Check .......................
Detect SAMSUNG [ec:76] 64MByte
BAD BLOCK SCAN -> Kernel, Ramdisk Bad Block [1]
CS8900 Init............................
Mac Address : [00 A2 55 F2 26 25]
Detect value : [3000:3000]
Chip ID : [0E63:000A]
..
Copy Kernel Image .....
Copy Ramdisk Image .....
Starting kernel [MARCH 303]...
Uncompressing Linux..................................................... done, .
Linux version 2.4.19-rmk7-pxa1 (root@localhost) (gcc version 3.2.1) #423 일 7월5
CPU: XScale-PXA255 revision 6
Machine: WWW.FALINUX.COM EZ-X5 for PXA255 Board
Ignoring unrecognised tag 0x00000000
Memory clock: 99.53MHz (*27)
Run Mode clock: 398.13MHz (*4)
Turbo Mode clock: 398.13MHz (*1.0, inactive)
On node 0 totalpages: 16384
zone(0): 16384 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: y initrd=0xa0800000,4M root=/dev/ram ramdisk=10240 consol9
Console: colour dummy device 80x30
Calibrating delay loop... 397.31 BogoMIPS
Memory: 64MB = 64MB total
Memory: 58908KB available (1416K code, 298K data, 68K init)
Dentry cache hash table entries: 8192 (order: 4, 65536 bytes)
Inode cache hash table entries: 4096 (order: 3, 32768 bytes)
Mount-cache hash table entries: 1024 (order: 1, 8192 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Using PXA255 frequency points.
Registering CPU frequency change support.
CPU clock: 398.131 MHz (99.000-400.000 MHz)
Starting kswapd
I2C: PXA algorithm module loaded.
I2C: Adding PXA-I2C-Adapter.
i2c-dev.o: Registered 'PXA-I2C-Adapter' as minor 0
I2C: Scanning bus (68)
I2C: Successfully added bus
Console: switching to colour frame buffer device 80x30
LCD resolution 640x480
initialize_kbd: Keyboard interface failed self test
Detected PS/2 Mouse Port.
PS2 Keyboard base:0xf1100000, irq:31 (gpio-8)
pty: 256 Unix98 ptys configured
keyboard: Timeout - AT keyboard not present?(ed)
keyboard: Timeout - AT keyboard not present?(f4)
Serial driver version 5.05c (2001-07-08) with no serial options enabled
ttyS00 at 0x0000 (irq = 15) is a PXA UART
ttyS01 at 0x0000 (irq = 14) is a PXA UART
ttyS02 at 0x0000 (irq = 13) is a PXA UART
mk712 device OK!
I2C: DS1307 RTC driver successfully loaded
eth0: cs8900 rev K Base 0xF1000300<6>, IRQ 44, MAC 00:A2:55:F2:26:25
RAMDISK driver initialized: 16 RAM disks of 10240K size 1024 blocksize
loop: loaded (max 8 devices)
Linux video capture interface: v1.00
SCSI subsystem driver Revision: 1.00
ac97_codec: AC97 Audio codec, id: 0x4352:0x5973 (Cirrus Logic CS4202)
NAND device: Manufacture ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MB 3,3V)
Creating 3 MTD partitions on "NAND 64MB 3,3V":
0x00000000-0x00100000 : "EZ-X5 Kernel partition"
0x00100000-0x00500000 : "EZ-X5 Ramdisk partition"
0x00500000-0x04000000 : "EZ-X5 Data partition 0"
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
host/sl811.c: v0.30 : Sl811 USB Host Controller Alternate Driver
usb.c: new USB bus registered, assigned bus number 1
host/sl811.c: USB SL811 at f2000000,f2000004, IRQ 35
hub.c: USB hub found
hub.c: 1 port detected
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 8192)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NetWinder Floating Point Emulator V0.95 (c) 1998-1999 Rebel.com
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 4096K
VFS: Mounted root (ext2 filesystem) readonly.
Freeing init memory: 68K
INIT: version 2.84 booting
EXT2-fs warning: maximal mount count reached, running e2fsck is recommended
INIT: Entering runlevel: 3
yaffs: dev is 7938 name is "1f:02"
hub.c: new USB device SL811-1, assigned address 2
mount: Mounting usbdevfs on /proc/bus/usb failed: Device or resource busy
Using /lib/pwc.o
pwc Philips PCA645/646 + PCVC675/680/690 + PCVC730/740/750 webcam module versio.
pwc Also supports the Askey VC010, Logitech Quickcam 3000 Pro, Samsung MPC-C10 ,
pwc the Creative WebCam 5, SOTEC Afina Eye and Visionite VCS-UC300 and VCS-UM10.
usb.c: registered new driver Philips webcam
Using /lib/pwcx-ezx5.o
insmod: Warning: kernel-module version mismatch
/lib/pwcx-ezx5.o was compiled for kernel version 2.4.20
while this kernel is version 2.4.19-rmk7-pxa1
Warning: loading pwcx-ezx5 will taint the kernel: non-GPL license - NDA-ed. Spw2
ee http://www.smcc.demon.nl/webcam/tainting.html
See http://wpwc Supports all cameras supported by the main module (pwc).
ww.tux.org/lkml/#export-tainted for information about tainted modules
Warning: loading pwcx-ezx5 will taint the kernel: forced load
Using /lib/motor_control_dev.o
Warning: loading motor_control_dev will taint the kernel: no lic Init madule, S]
ense
See http://www.tux.org/lkml/#export-tainted for informat/nctrl :0, duty : 6, s
Interrupt Motor Register Ok...
Interrupt Timer Register Ok...
Starting system logger: syslogd
Starting INET services: inetd
Welcome to J.D&T EZ-X5 ( www.falinux.com )
XScale(PXA255) Linux
ez-x5 login: usb_control/bulk_msg: timeout
usb.c: failed to set device 2 default configuration (error=-110)
hub.c: new USB device SL811-1, assigned address 3
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=3 (error=-110)
Welcome to J.D&T EZ-X5 ( www.falinux.com )
XScale(PXA255) Linux
ez-x5 login:
----------------------------------------------------------------------------------
부팅시 메시지 입니다...위의 부팅은 rc.local 파일을 수정 해서 부팅과 동시에 모듈이 올라가게 수정 했습ㄴ다. 수정 내용은 처음 질문 글과 같습니다....
l------------------------------------------------------------------------------
lsmod 명령어 실행시
Module Size Used by Tainted: PF
motor_control_dev 5392 0 (unused)
pwcx-ezx5 89044 0 (autoclean) (unused)
pwc 42008 0 [pwcx-ezx5]
-------------------------------------------------------------------------
mvc 실행시 오류 내용
[root@ez-x5 /root]$ mvc
MVC version 0.8.9
Press CTRL-Z to switch program to daemon mode.
Can't open device /dev/video0
v4l init fault!
-----------------------------------------------------
