제공되는 시디에 있는 이미지로 EZ-X5(v1.1)에 올리면 다음과 같은 메세지가 나옵니다

사용한 이미지 파일 :
ezboot.x5
ramdisk.x5.pcmcia-10M.gz
zImage.x5.pcmcia

무선랜 : 삼성매직랜 (swl-2100N)

----------------------------------------
Copy Kernel Image .....
Copy Ramdisk Image .....
Starting kernel [MARCH 303]...
Uncompressing Linux.................................................... done, b.
Linux version 2.4.19-rmk7-pxa1 (root@jdt) (gcc version 3.2.1) #272 Mon Jan 5 124
CPU: XScale-PXA255 revision 6
Machine: WWW.FALINUX.COM EZ-X5 for PXA255 Board
Ignoring unrecognised tag 0x00000000
Memory clock: 99.53MHz (*27)
Run Mode clock: 398.13MHz (*4)
Turbo Mode clock: 398.13MHz (*1.0, inactive)
On node 0 totalpages: 16384
zone(0): 16384 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: y  initrd=0xa0800000,4M root=/dev/ram ramdisk=10240 consol9
Console: colour dummy device 80x30
Calibrating delay loop... 397.31 BogoMIPS
Memory: 64MB = 64MB total
Memory: 58920KB available (1384K code, 319K data, 68K init)
Dentry cache hash table entries: 8192 (order: 4, 65536 bytes)
Inode cache hash table entries: 4096 (order: 3, 32768 bytes)
Mount-cache hash table entries: 1024 (order: 1, 8192 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Using PXA255 frequency points.
Registering CPU frequency change support.
CPU clock: 398.131 MHz (99.000-400.000 MHz)
Starting kswapd
Console: switching to colour frame buffer device 80x30
LCD resolution 640x480
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with no serial options enabled
ttyS00 at 0x0000 (irq = 15) is a PXA UART
ttyS01 at 0x0000 (irq = 14) is a PXA UART
ttyS02 at 0x0000 (irq = 13) is a PXA UART
mk712 device OK!
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
eth0: cs8900 rev J Base 0xF1000300<6>, IRQ 44, MAC 00:A2:55:F2:26:25
RAMDISK driver initialized: 16 RAM disks of 10240K size 1024 blocksize
loop: loaded (max 8 devices)
NAND device: Manufacture ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MB 3,3V)
Creating 3 MTD partitions on "NAND 64MB 3,3V":
0x00000000-0x00100000 : "EZ-X5 Kernel partition"
0x00100000-0x00500000 : "EZ-X5 Ramdisk partition"
0x00500000-0x04000000 : "EZ-X5 Data partition 0"
MMC subsystem, $Revision: 0.3.1.14 $
MMC block device driver, $Revision: 0.3.1.16 $
PXA250 MMC controller driver, $Revision: 0.3.1.12 $
Linux Kernel Card Services 3.1.22
  options:  none
Intel PXA250/210 PCMCIA (CS release 3.1.22)
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 8192)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NetWinder Floating Point Emulator V0.95 (c) 1998-1999 Rebel.com
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 4096K
VFS: Mounted root (ext2 filesystem) readonly.
Freeing init memory: 68K
INIT: version 2.84 booting
INIT: Entering runlevel: 3
yaffs: dev is 7938 name is "1f:02"
SIOCADDRT: Network is unreachable
Starting system logger:  syslogd
Starting INET services:  inetd


Welcome to J.D&T EZ-X5 ( www.falinux.com )
XScale(PXA255) Linux
ez-x5 login:

----------------------------------------

문제는 보드에서 무선랜은 인식을 한것 같은데 eth1이 생성이 안됩니다

[root@ez-x5 /root]$ cd /proc/bus/pccard/00
[root@ez-x5 00]$ cat status
k_flags  : detect ready bvd1 vs_3v
status   : SS_DETECT SS_READY SS_POWERON SS_BATWARN SS_3VCARD
mask     : SS_DETECT
cs_flags : SS_OUTPUT_ENA
Vcc      : 33
Vpp      : 33
irq      : 0
I/O      : 165 (180)
attribute: 300 (301)
common   : 250 (271)
[root@ez-x5 00]$ cd /proc/hermes
[root@ez-x5 hermes]$ ls
[root@ez-x5 hermes]$

이런 상황에서 어떻게 해야 eth1을 잡을수 있을까요?