usb키보드/마우스잡는 방법을 알고싶습니다...
dmesg내용중 usb관련내용은 아래와 같습니다...

***************************************

usb.c: registered new driver hub
host/sl811.c: v0.30 : Sl811 USB Host Controller Alternate Driver
usb.c: new USB bus registered, assigned bus number 1
host/sl811.c: USB SL811 at f2000000,f2000004, IRQ 35
hub.c: USB hub found
hub.c: 1 port detected
usb.c: registered new driver usbkbd
usbkbd.c: :USB HID Boot Protocol keyboard driver

***************************************

usb는 인식하는것 같은데 어떤문제인지를 모르겠습니다...ㅡㅡ;
usb를 확인한 결과입니다...

********** usbmessage **********

ez-x5_good login: usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=2 (error=-110)
hub.c: new USB device SL811-1, assigned address 3
[root@ez-x5_good /root]$ usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=3 (error=-110)

********** driver usb message **********

[root@ez-x5_good driver]$ cat pxausb
PXA USB Controller Core
Active Client: none
USB state: powered (zombie) 0
           ep0 bytes read: 0
        ep0 bytes written: 0
   ep0 FIFO read failures: 0
  ep0 FIFO write failures: 0
                                                                                                
                                                                                                
UDC Control Register
                    Value: 000000A0
              UDC Enabled: NO
               UDC Active: NO
Suspend/Resume interrupts: YES
  Reset interrupts masked: YES
            Reset pending: NO
          Suspend pending: NO
           Resume pending: NO
[root@ez-x5_good driver]$ pwd
/proc/driver
[root@ez-x5_good driver]$

***** usb check test *****

[root@ez-x5_good usb]$ cat drivers
         usbdevfs
         hub
         usbkbd
         usb-storage
[root@ez-x5_good usb]$ cat devices
T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 1
B:  Alloc=  0/900 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 1.10 Cls=09(hub  ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 0.00
S:  Product=USB SL811HS Root Hub
S:  SerialNumber=0
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   2 Ivl=255ms
[root@ez-x5_good usb]$ pwd
/proc/bus/usb

문제점을 잘몰라 usb관련 커널 프로그래밍도 보았으나 감이 오질 않습니다...ㅡㅡ;
통신방식에 대한 내용은 감잡았은것 같은데(?)...무엇을 수정해야하는지를 모르겠어요...
usb키보드/마우스를 잡아보고 싶습니다...
혹시 설정관련문서가 있으시다면 조언부탁드립니다...
왕초보라 귀찮은 질문이 되지는 않았는지...ㅡㅡ;
관련문서가 있으시면 따라해볼수 있는 영광을 주시면 감사하겠습니다...^^
추운날씨에 감기조심하셔요...