도와주세요!!
1)
[root@falinux ~]$ mount -t nfs 192.168.30.38:/opt /opt
mount: RPC: Unable to send; errno = Network is unreachable
mount: nfsmount failed: Bad file descriptor
mount: Mounting 192.168.30.38:/opt on /opt failed: Bad file descriptor
2)
[root@falinux ~]$mount -t nfs -o nolock 192.168.30.38:/opt /opt
nfs: server 192.168.30.38 not responding, still trying
3)
[root@falinux ~]mount -t nfs -o nolock,rsize=1024,wsize=1024 192.168.30.38:/opt /opt
> 간혹 되는 경우 있으나, 역시 nfs: server 192.168.30.38 not responding, still trying 메시지 뜨거나, 명령치면 먹통됨.
4)
linux <-> target b/d 양방향간 ping 시에 ping 이 멈추었다 나가다 반복합니다. packets loss 87% 나오네요 ㅡㅡ;
( hub사용중입니다 )
위와 같은 에러가 발생하며, 아주 가끔씩 연결이되며, 명령어를 치면 약 2-3분 후에 실행이 되곤합니다..
제 설정 상태 : VMWARE 사용
LINUX : 192.168.30.38 / 255.255.255.0 / 192.168.30.1
TARGET : 192.168.30.39 /255.255.255.0
export file 내용 : /opt 192.168.30.0/255.255.255.0(rw,insecure,subtree_check,sync)
위와 같이 설정된 상태입니다..
그리고, 이 보드 외의 다른 mips core ( au1250 아님 ) 보드가 있는데요, 그 보드는 아주 nfs 설정이 바로됩니다..
동일 설정에서 바로 실행이 되는데요, au1250에서가 안되고있습니다..
무슨 문제가 있는 것인지요???
- target b/d network 정보
eth0 Link encap:Ethernet HWaddr 00:A9:09:26:00:1C
inet addr:192.168.30.39 Bcast:192.168.30.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:564 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:42391 (41.3 KiB) TX bytes:0 (0.0 B)
Interrupt:34 DMA chan:ff
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
문제 원인 ]
> 회사내부 내트웤서버에서 각 IP 에 해당하는 MAC을 고정으로 사용하도록 설정 되는 문제.
> IP 3개가 모두 노트북(2개 - 윈도우,리눅스용도 ) MAC, 나머지 1개는 - 기존에 사용하였던 MIPS 보드 로 이미 고정이 되어있어서.
> 이번에 구매한 1250을 연결하니, 기존에 사용하던 MIPS 보드의 MAC주소와 틀려서, IP연결이 되지 않는 문제였습니다.
2틀간 삽질하다.. 정보팀에 문의한 결과 ㅡㅡ;; 정보팀이 저렇게 고정으로 된다고 알려주네요...
고로, 3번째 보드에 할당한 IP에 해당하는 MAC을 고정시키지 않도록 설정해주니 해결되었습니다.
혹시 비슷한 경우 있으신 분들은 정보팀에 문의해 보세요~~ ^^;
부트로더에서 ping 명령이나 tftp 명령을 하여 보시기 바랍니다.
만일 부트로더에서도 되지 않는다면 AS 을 받으세요
다른 보드에서는 잘 된다고 하니 환경을 의심하기는 힘들군요 ^^