Copy Kernel Image .....
Copy Ramdisk Image .....
Starting kernel [MARCH 3007]...
kernel command [EZBOOT mem=64M initrd=0x30800000,5M root=/dev/ram0 rw ramdisk=16384 console=ttySAC2,115200    ip0=192.168.1.80 mac=00:FA:01:A2:13:04 netmask=255.255.255.0 gw=192.168.1.254 host=192.168.1.203 nandparts=2,8,54 ]
Uncompressing Linux................................................................................................... done, booting the kernel.
Linux version 2.6.30 (jjlee@eems) (gcc version 3.4.3) #17 Fri Apr 15 10:21:03 KST 2011
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
CPU: VIVT data cache, VIVT instruction cache
Machine: SMDK2440
Memory policy: ECC disabled, Data cache writeback
CPU S3C2440A (id 0x32440001)
S3C24XX Clocks, (c) 2004 Simtec Electronics
S3C244X: core 399.000 MHz, memory 133.000 MHz, peripheral 66.500 MHz
CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: EZBOOT mem=64M initrd=0x30800000,5M root=/dev/ram0 rw ramdisk=16384 console=ttySAC2,115200    ip0=192.168.1.80 mac=00:FA:01:A2:13:04 netmask=255.255.255.0 gw=192.168.1.254 host=192.168.1.203 nandparts=2,8,54
NR_IRQS:85
irq: clearing pending status 00000400
irq: clearing subpending status 00000080
PID hash table entries: 256 (order: 8, 1024 bytes)
Console: colour dummy device 80x30
console [ttySAC2] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 56512KB available (2844K code, 240K data, 120K init, 0K highmem)
Calibrating delay loop... 199.06 BogoMIPS (lpj=497664)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 936 bytes
NET: Registered protocol family 16
S3C2440: Initialising architecture
S3C2440: IRQ Support
S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics
DMA channel 0 at c4808000, irq 33
DMA channel 1 at c4808040, irq 34
DMA channel 2 at c4808080, irq 35
DMA channel 3 at c48080c0, irq 36
S3C244X: Clock Support, DVS off
bio: create slab <bio-0> at 0
SCSI subsystem initialized
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 5120K
NetWinder Floating Point Emulator V0.97 (double precision)
audit: initializing netlink socket (disabled)
type=2000 audit(0.415:1): initialized
yaffs Apr 14 2011 18:27:29 Installing.
msgmni has been set to 120
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
s3c2440-uart.0: s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440
s3c2440-uart.1: s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440
s3c2440-uart.2: s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440
brd: module loaded
loop: module loaded
Driver 'sd' needs updating - please use bus_type methods
smc91x.c: v1.1, sep 22 2004 by Nicolas Pitre <nico@cam.org>
eth0: SMC91C11xFD (rev 2) at c480c300 IRQ 60 [nowait]
eth0: Ethernet addr: 00:fa:01:a2:13:04
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c2440-nand s3c2440-nand: Tacls=3, 22ns Twrph0=8 60ns, Twrph1=3 22ns
NAND device: Manufacturer ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MiB 3,3V 8-bit)
Scanning device for bad blocks
Creating 3 MTD partitions on "NAND 64MiB 3,3V 8-bit":
0x000000000000-0x000000200000 : "boot/config/logo partition"
0x000000200000-0x000000a00000 : "kernel/ramdisk partition"
0x000000a00000-0x000004000000 : "yaffs partition"
mice: PS/2 mouse device common for all mice
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
TCP cubic registered
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RAMDISK: gzip image found at block 0
VFS: Mounted root (ext2 filesystem) on device 1:0.
Freeing init memory: 120K
INIT: version 2.86 booting
mount: Mounting /dev/root on / failed: Invalid argument  <====  여기 어디를 보아야 할지...?
INIT: Entering runlevel: 3
eth0: link down
yaffs: dev is 32505858 name is "mtdblock2"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.2, "mtdblock2"
yaffs: auto selecting yaffs1
yaffs_read_super: isCheckpointed 0
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
Starting system logger:                                    [  OK  ]
Starting INET services:                                    [  OK 

Welcome

Linux Kernel 2.6.30
JJLEE login:

조언 구합니다.