도와주세요!!
Creating 8 MTD partitions on "NAND 1GiB 3,3V 8-bit":
0x000000000000-0x000000400000 : "Bootloader"
0x000000400000-0x000001100000 : "Kernel+Ramdisk"
0x000001100000-0x000001b00000 : "Kernel2"
0x000001b00000-0x000011b00000 : "system"
0x000011b00000-0x00001e300000 : "userdata"
0x00001e300000-0x00002e300000 : "cache"
0x00002e300000-0x00003ab00000 : "Application"
0x00003ab00000-0x000040000000 : "Application2"
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 79, io mem 0x74300000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
s3c-udc : S3C HS USB OTG Device Driver, (c) 2008-2009 Samsung Electronics
s3c-udc : version 15 March 2009 (DMA Mode)
g_ether gadget: using random self ethernet address
g_ether gadget: using random host ethernet address
usb0: MAC 96:e8:0e:8c:a7:55
usb0: HOST MAC 6a:f2:ec:f7:b5:18
g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
g_ether gadget: g_ether ready
Registered gadget driver 'g_ether'
mice: PS/2 mouse device common for all mice
input: falinux-gpio-keys as /devices/platform/falinux-gpio-keys/input/input0
Ok! falinux gpio key register
S3C Touchscreen driver, (c) 2008 Samsung Electronics
S3C TouchScreen got loaded successfully : 12 bits
input: S3C TouchScreen as /devices/virtual/input/input1
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c2410_rtc: tick irq 34, alarm irq 92
s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling
s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0
i2c /dev entries driver
s3c2440-i2c s3c2440-i2c.0: slave address 0x10
s3c2440-i2c s3c2440-i2c.0: bus frequency set to 377 KHz
s3c2440-i2c s3c2440-i2c.0: i2c-0: S3C I2C adapter
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133000000 Hz)
s3c-sdhci s3c-sdhci.0: clock source 1: hsmmc (133000000 Hz)
s3c-sdhci s3c-source 2: mmc_bus (24000000 Hz)
mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
logger: created 64K log 'log_main'
logger: created 256K log 'log_events'
logger: created 64K log 'log_radio'
Advanced Linux Sound Architecture Driver Version 1.0.18a.
No device for DAI s3c64xx-ac97
WM9713/WM9714 SoC Audio Codec 0.15
asoc: AC97 HiFi <-> s3c64xx-ac97 mapping ok
ALSA device list:
#0: SMDK6400 (WM9713)
oprofile: using arm/armv6
IPv4 over IPv4 tunneling driver
GRE over IPv4 tunneling driver
TCP cubic registered
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
lib80211: common routines for IEEE802.11 drivers
VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 5
s3c2410-rtc s3c2410-rtc: hctosys: invalid date/time
RAMDISK: Compressed image found at block 0
invalid compressed format (err=1)
VFS: Mounted root (ext2 filesystem) readonly on device 1:0.
Freeing init memory: 292K
Failed to execute /. Attempting defaults...
INIT: version 2.86 booting
INIT: Entering runlevel: 3
INIT: Id "T0" respawning too fast: disabled for 5 minutes
MTD 의 주소를 조금 만져주고 EZ 부트로더 config 부분과 main 부분을 조금 고쳤습니다.
램디스크가 풀리긴 하는데.....
이러한 현상은 무엇 때문에 일어나는 일인가요?