G100 보드에서 usb 호스트에 꼽으면

usb 1-2: device not accepting address 7, error -71

hub 1-2:1.0: unable to enumerate USB device on port 7

이렇게 뜨면서 인식이 안되네요

lsusb 하면 usb 2.0 hub 만 뜨고

usb 메모리를 연결해도 그렇고 usb 마우스를 연결해도 그렇고

커널에 usb support 관련 포팅이 안된건지

usb를 전혀 인식하지 못하네요

6410보드 쓸때는 연결하면 lsusb에 목록이 떴었는데

어떻게 해야되나요

부팅 메시지 올려 봅니다.

lk_csis: no parent clock specified
S5PV210: PLL settings, A=1000000000, M=667000000, E=80000000 V=54000000
S5PV210: ARMCLK=1000000000, HCLKM=200000000, HCLKD=166750000
HCLKP=133400000, PCLKM=100000000, PCLKD=83375000, PCLKP=66700000
sclk_csis: no parent clock specified
s5pv310: 25165824 bytes system memory reserved for fimd at 0x21800000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 65024
Kernel command line: EZBOOT mem=256M initrd=0x21000000,8M root=/dev/ram0 ramdisk
=24576 console=ttySAC2,115200    ip0=192.168.10.210 mac=00:FA:01:A2:13:04 netmas
k=255.255.0.0 gw=192.168.10.1 host=192.168.10.20 nandparts=1,1,2,6,8,0,0,0 ezb_m
mc=0x5 ezb_ac97=1 ezb_fb=1 
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 256MB = 256MB total
Memory: 222080k/222080k available, 40064k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    DMA     : 0xff000000 - 0xffe00000   (  14 MB)
    vmalloc : 0x90800000 - 0xe0000000   (1272 MB)
    lowmem  : 0x80000000 - 0x90000000   ( 256 MB)
    modules : 0x7f000000 - 0x80000000   (  16 MB)
      .init : 0x80008000 - 0x80085000   ( 500 kB)
      .text : 0x80085000 - 0x80459000   (3920 kB)
      .data : 0x80476000 - 0x804ada40   ( 223 kB)
SLUB: Genslabs=9, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
        RCU-based detection of stalled CPUs is disabled.
        Verbose stalled-CPUs detection is disabled.
NR_IRQS:393
VIC @f4000000: id 0x00041192, vendor 0x41
VIC @f4010000: id 0x00041192, vendor 0x41
VIC @f4020000: id 0x00041192, vendor 0x41
VIC @f4030000: id 0x00041192, vendor 0x41
Console: colour dummy device 80x30
console [ttySAC2] enabled
Calibrating delay loop... 996.14 BogoMIPS (lpj=2490368)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
S5PV210 Power Domain API Enable
S5PV210: Initializing architecture
bio: create slab <bio-0> at 0
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
s3c-i2c s3c2440-i2c.0: slave address 0x10
s3c-i2c s3c2440-i2c.0: bus frequency set to 65 KHz
s3c-i2c s3c2440-i2c.0: i2c-0: S3C I2C adapter
s3c-i2c s3c2440-i2c.1: slave address 0x10
s3c-i2c s3c2440-i2c.1: bus frequency set to 65 KHz
s3c-i2c s3c2440-i2c.1: i2c-1: S3C I2C adapter
s3c-i2c s3c2440-i2c.2: slave address 0x10
s3c-i2c s3c2440-i2c.2: bus frequency set to 65 KHz
s3c-i2c s3c2440-i2c.2: i2c-2: S3C I2C adapter
Advanced Linux Sound Architecture Driver Version 1.0.23.
cfg80211: Calling CRDA to update world regulatory domain
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 5, 163840 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
UDP hash table entries: 128 (order: 0, 6144 bytes)
UDP-Lite hash table entries: 128 (order: 0, 6144 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (no cpio magic); looks like an initrd
Freeing initrd memory: 8192K
S5PV210 ADC driver, (c) 2010 Samsung Electronics
msgmni has been set to 449
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
         s3cfb_probe
s3cfb s3cfb: fifo underrun trace
s3cfb s3cfb: [fb0] dma: 0x21800000, cpu: 0x91000000, size: 0x002ee000
Console: switching to colour frame buffer device 100x30
FIMD src sclk=166750000
  vclk=24403000, vclk-div=7
s3cfb s3cfb: registered successfully
Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
s5pv210-uart.0: ttySAC0 at MMIO 0xe2900000 (irq = 16) is a S3C6400/10
s5pv210-uart.1: ttySAC1 at MMIO 0xe2900400 (irq = 20) is a S3C6400/10
s5pv210-uart.2: ttySAC2 at MMIO 0xe2900800 (irq = 24) is a S3C6400/10
s5pv210-uart.3: ttySAC3 at MMIO 0xe2900c00 (irq = 28) is a S3C6400/10
brd: module loaded
loop: module loaded
usbcore: registered new interface driver ub
S3C NAND Driver, (c) 2008 Samsung Electronics
NAND device: Manufacturer ID: 0xec, Chip ID: 0xdc (Samsung NAND 512MiB 3,3V 8-bi
t)
S3C NAND Driver is using hardware ECC-8
Creating 2 MTD partitions on "s3c-nand":
0x000000000000-0x000000400000 : "bootloader+config+logo"
0x000000400000-0x000001200000 : "kernel+ramdisk"
S3C NAND Driver is using hardware ECC-1
Creating 1 MTD partitions on "s3c-nand":
0x000001200000-0x000020000000 : "app1"
ASIX AX88796B Ethernet Adapter:v2.1.0
AX88796B: MAC ADDRESS 00:fa:01:a2:13:04:
AX88796B:  found at 0x88000000, using IRQ 42.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
s5p-ehci s5p-ehci: s5pv210 EHCI
s5p-ehci s5p-ehci: new USB bus registered, assigned bus number 1
s5p-ehci s5p-ehci: irq 87, io mem 0xec200000
s5p-ehci s5p-ehci: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
mice: PS/2 mouse device common for all mice
S5P Touchscreen driver, (c) 2008 Samsung Electronics
remap to 0xE1701000. done
S5P TouchScreen got loaded successfully : 12 bits
input: S5P TouchScreen as /class/input/input0
rtc-ds1307 0-0068: rtc core: registered ds1307 as rtc0
rtc-ds1307 0-0068: 56 bytes nvram
i2c /dev entries driver
Linux video capture interface: v2.00
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133400000 Hz)
s3c-sdhci s3c-sdhci.0: clock source 1: hsmmc (133400000 Hz)
s3c-sdhci s3c-sdhci.0: clock source 2: sclk_mmc (47642857 Hz)
mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA
s3c-sdhci s3c-sdhci.2: clock source 0: hsmmc (133400000 Hz)
s3c-sdhci s3c-sdhci.2: clock source 1: hsmmc (133400000 Hz)
s3c-sdhci s3c-sdhci.2: clock source 2: sclk_mmc (47642857 Hz)
mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.2] using ADMA
dma-pl330 dma-pl330.0: Loaded driver for PL330 DMAC-267056
dma-pl330 dma-pl330.0:  DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
dma-pl330 dma-pl330.1: Loaded driver for PL330 DMAC-267056
dma-pl330 dma-pl330.1:  DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
asoc: AC97 HiFi <-> s3c-ac97 mapping ok
AC97: Unable to activate!
AC97: Unable to activate!
AC97: Unable to read!
AC97: Unable to activate!
AC97: Unable to activate!
AC97: Unable to read!
AC97: Unable to activate!
AC97: Unable to activate!
AC97: Unable to read!
Failed to reset wm9715: AC97 link error
ALSA device list:
  No soundcards found.
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2
rtc-ds1307 0-0068: setting system clock to 2013-02-18 10:05:31 UTC (1361181931)
RAMDISK: gzip image found at block 0
VFS: Mounted root (ext2 filesystem) readonly on device 1:0.
Freeing init memory: 500K
INIT: version 2.86 booting
EXT2-fs (ram0): warning: checktime reached, running e2fsck is recommended
INIT: Entering runlevel: 3
AX88796B:  The media mode is autosense.
yaffs: dev is 32505858 name is "mtdblock2"
yaffs: passed flags ""
Starting system logger: [  OK  ]
Starting hotplug eth0: link up, 100Mbps, Full-duplex
[  OK  ]

Welcome to FALinux (www.falinux.com)
Linux Kernel 2.6.35-falinux
falinux login: